.
.
Download / Read Online Carrier phoenix ultra parts manual
.
.
.
.
Top element. S MANUAL TRAILER REFRIGERATION UNITS WITH STANDARD MICROPROCESSOR. AFETY Your Carrier Transicold refrigeration unit has been designed with the safety of the operator in mind. If a problem occurs, please refer to the information on this decal, and make a note of the model and serial number before calling for assistance. This information will be needed when you contact a technician or Carrier Transicold Service Engineer so that they may properly assist you. The microprocessor controller will run a self test. All of the mode lights will light, all of the segments on the display will be turned on. The display will then show the setpoint temperature on the left and the box temperature of the trailer on the right. CONTINUOUS toggle key to place unit in Continuous Run Mode . Press FUNCTION CHANGE key until AUTO OP or MAN OP is displayed. When the unit is in Continuous Run mode and set for Manual Operation, the unit must be started manually WARNING Under no circumstances should ether or any other. S STANDBY UNIT MANUAL PRETRIP DATA CONTINUOUS CHECK DEFROST ENGINE. The PRETRIP mode is for checking unit operation and evaluating operation of all modes. The unit will cycle thru all modes of operation at 30 second intervals. When Pretrip is complete, Pretrip mode is terminated and the unit returns to normal operation. The final PRETRIP mode is Defrost. HANGING ETPOINT Press UP arrow key to increase displayed setpoint. Press DOWN arrow key to decrease displayed setpoint. F F F F STANDBY POWER ON SETPOINT. The controller always retains the last entered setpoint in memory. XT products, 10 minutes for all others. If the unit fails to start, shuts down on a safety, or fails to run for the minimum run time, three consecutive times, the fault light is on. In the Continuous Run mode, the diesel engine will run continuously providing constant air flow and temperature control to the product. Continuous Run operation is normally used for perishable loads. Stop and Continuous operation may be tied to the setpoint ranges frozen perishable. Defrost is initiated automatically at preset intervals by the defrost timer in the microprocessor. Defrost is initiated by the defrost air switch. Press FUNCTION CHANGE key until Function to be changed is displayed. BY D D D D E E E E F F F F R R R R 1 1 1 1 2 2 2 2 . H H H H DEFROST STANDBY POWER ON. UNCTION HANGE ARAMETERS The following table has columns for Code and English displays. Change Functional Parameter to Code to see Code display format. Function Codes CODE ENGLISH DATA DEFR Defrost Time Interval FN1 ON HIGH AIR High Air Flow FN1 OFF NORM AIR Normal Air Flow OFF T. The following table has columns for Code and English displays. Box Temperature alternates with alarm display. When fault light is on, check display for alarm message. BY E E E E N N N N G G G G O O O O I I I I L L L L. Display CODE ENGLISH ALARM DESCRIPTION ENG OIL Low Oil Pressure High Coolant ENG HOT Temperature HI PRESS High Pressure STARTFAIL. Standby Operation is for Ultra NDM units only. Check for proper motor rotation. Condenser air must be drawn into unit. To reverse rotation, stop unit, disconnect power cord and change polarity of plug. The diesel engine will stop and the microprocessor controller will turn off. These checks take only a few minutes. This will remove much of the heat from the inside of the trailer, and give the product better protection when it is loaded. D If possible, place the unit in a defrost cycle immediately before loading. Product stacking is another important factor in protecting the product. These are included for reference only and should not be considered preemptive of the setpoint required by the shipper or receiver. More detailed information can be obtained from your Carrier Transicold dealer. If, however you run into problems the following section may be of assistance. If you do not find the trouble that you have experienced listed, please call your Carrier Transicold dealer for assistance. USES The fuses that protect the circuits of the Microprocessor control system are located in the control box on the roadside of the unit. They may be accessed by loosening the screws that hold the control box cover closed. The cover can be removed and hung below the control box by its tethers as shown below. CI or higher rating or Mobil Delvac 1 synthetic oil. The use of any oil that does not meet this rating may affect the warranty on the engine in the unit. AINTENANCE CHEDULE For the most reliable operation and for maximum life, your unit requires regular maintenance. This includes oil and filter changes, fuel and air filter replacement, coolant replacement. ERVICE D Drain the engine oil and replace oil filter. Extended life coolant should be replaced every five years. A more detailed description of service requirements and procedures can be found in the Service and Operations Manual for your unit. This manual may be obtained from any Carrier Transicold dealer. RIMING YSTEM The mech filexlib.
.
Carrier phoenix ultra parts manual lawn
Carrier phoenix ultra parts brugervejledning
Carrier phoenix ultra parts owner guide
Carrier phoenix ultra parts manuaalinen
Carrier phoenix ultra parts handleiding
