.
.
Download / Read Online Arcweld 200i-s inverter dc manual pdf
.
.
.
.
It is prohibited to reproduce this documentation, or any part thereof, without the prior written authorisation of Magma Mekatronik Makine Sanayi ve Ticaret A. Magma Mekatronik may modify the information and the images without any prior notice. Be Sure To Follow All Safety Rules In This Manual! DC MMA welding machine designed to weld stick electrodes up to 4 mm. Monostick 200i can also be used with long welding cables up to 25 mt. The machine is fan cooled and thermally protected against over heating. To unpack your purchased welding machine to comply with the truck transport regulations, first tear the cutter, then cut the ring and lift the machine down the pallet to comply with the truck transport regulations. Make sure you receive your order in full. If any material is missing or damaged, contact your place of purchase immediately. In the case of a damaged delivery, draw up a record, take a picture of the damage and report to the transport company together with a photocopy of the delivery note. If the problem persists, contact the customer service. Necessary precautions should be taken during transportation of the machine. Do not lift the machine with the gas cylinder. Place the power supply on a hard, level and level surface where it will not fall or tip over. For better performance, place the machine at least 30 cm away from surrounding objects. Pay attention to overheating, dust and moisture around the machine. Do not operate the machine in direct sunlight. C, operate the machine at a lower current or at a lower cycle rate. Avoid welding with wind and rain outdoors. If welding is required in such cases, protect the welding area and the welding machine with curtains and awnings. When positioning the machine, make sure that materials such as walls, curtains, panels, etc. If welding inside, use a suitable smoke extraction system. Use breathing apparatus if there is a risk of inhaling welding fumes and gas indoors. Observe the duty cycle rates specified on the product label. Frequent exceeding duty cycle rates can damage the machine and void the warranty. Use the appropriate fuse for your system. Connect the ground wire as close to the welding area as possible. Do not allow welding current to pass through elements other than welding cables, eg the machine itself, the gas cylinder, the chain, the bearing. When the gas cylinder is placed on the machine, immediately fasten the chain to secure the gas cylinder. If you do not place the gas cylinder on the machine, fasten it to the wall with a chain. The electrical outlet on the back of the machine is for the CO heater. NEVER connect a device other than a CO heater to the CO socket! Check the mains voltage before connecting the machine to the mains. Connect the earth clamp tightly to the workpiece as close as possible to the welding area. Adjust the desired current and the machine is ready to weld. LEDs are on and the cooling fan is working. TIG torch with a valve should be used. Strictly follow the instructions in safety rules while servicing the machine. The above mentioned periods are the maximum ones that should be applied if no problems are encountered in your device. Depending on the work load and contamination of your work environment, you can repeat the above processes more frequently. Hot weather or working in high current values for long time may cause this. Let the machine on for a while in order to cool down itself with the cooling fan. Then the mains input is at low voltage, In this case close the machine. If you see the yellow led is lighting then make control of your mains input. If there is not a problem with your mains voltage then contact to your authorized technical service. If the mains voltage is low, output current of machine can be set to 130A maximum. Magma Mekatron k Mak ne Sanay ve T caret A. Appropr ate for profess onal and ndustr al usage. We declare that the above mentioned products comply wth the standard. This declaration wall loose ts validity in case of modification on the welding machine without our written authorization. Manual carefully before using the machine. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. The resource you are looking for has been removed, had its name changed, or is temporarily unavailable. filexlib.
.
Arcweld 200i-s inverter dc pdf gebruiksaanwijzing
Arcweld 200i-s inverter dc pdf user manual
Arcweld 200i-s inverter dc pdf owner guide
Arcweld 200i-s inverter dc pdf user guide
Arcweld 200i-s inverter dc pdf prirucka
